Just about every person seems to have their unique theory when it comes to How to Install a Bathtub.
Setting up a bathtub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately tough job. If the old bathtub is easily available, the task can relocate speedily; if you have to open up a wall to get rid of the old tub and position the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub as well as set in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable attempting it. As opposed to employing a service provider to take over a halfway-completed task, it is better to take into consideration using one before you start. Chances are you may require a professional plumber to make tube links.
This article will certainly help you set up a brand-new bathtub in your shower room if you have already gotten a brand-new tub and don't require to change the plan of your previous water supply pipes.
Your devices and material list should make up the following:
Preparing for the Setup
To start with, the sustaining frame supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to stop pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of removing the existing taps can be fairly bothersome as a result of the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Tub
Using both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four little points.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the bath tub up until the spirit level reviews level.
To install faucets, fit the bottom of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as also examine the overflow outlet as well as the regular outlet for leakages.
Finally, repair the bathroom paneling as described in the maker's user's manual. Tiling as well as securing around the bath tub ought to wait up until the bath tub has been made use of at least when as this will certainly resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Safeguard the faucet in position with the manufacturer offered backnut. When the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to crack a rigid seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as installations. They are marketed in tubes as well as cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can fracture fairly very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the tiles making use of water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading about How to Install a Bathtub Yourself? Create feedback down below. We would be pleased to know your thoughts about this entry. In hopes that you visit us again soon. Liked our piece of writing? Please share it. Help someone else find it. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Quote